The TB40-1 limit controller has been type tested to DIN standards.
The TB40-1 can be used for heating and refrigeration processes. It is suitable for all thermocouple types and resistance type sensors. It is particularly designed for use in:
All applications where an over or under temperature fault condition could present fire hazard or other hazard
Heating system in buildings to DIN EN 12828
Large hot-water boilers to DIN EN 12953-6
Thermal transfer plants with organic heat transfer media to DIN 4754
Oil-fired installations to DIN 4755
| Manufacturer | |
|---|---|
| Series | |
| Din Size | |
| Dimensions and Size | 96mm x 48mm x 118mm (HxWxD), 1/8 DIN |
| Connectors | Pin or screw terminals |
| Primary Input Type | Universal (TC, RTD, DC linear mA/mV) |
| Output Type | Relay |
| Max. Number of Outputs: | 3 |
| Control Type: | Temperature limiter |
| Power Supply: | 100–240V AC 50–60Hz, 20-48V AC 50/60 Hz, 22-65V DC |
| Panel Sealing: | IP65 |
| Certifications: | CE, Type tested to EN 14597 (replaces DIN 3440), cULus |
| Software Tools: | BlueControl |
Only logged in customers who have purchased this product may leave a review.
The 8170+ single loop controller is part of the Plus series range and has 3-point stepping control designed specifically for open loop, valve motor drive (VMD) applications.
The 8170+ incorporates advanced tuning algorithms, with selectable pre-tune and self-tuning for easier setup. The self-tune also reduces output activity to an absolute minimum without compromising control quality, thereby reducing wear and tear on mechanical components such as valves, contactors and relays. In test, these controls have cut down valve oscillation from 30 to 40 times a minute to just a few. Pre-tune plus self-tuning has also been shown to get on control up to 3 times faster.
In addition to the VMD outputs, further output options exist which can be designated as outputs for alarms, 24 VDC transmitter power supply, retransmit process value or setpoint.
Button Text| Manufacturer | Series | Din Size |
|---|---|---|
| West Control Solutions | 8170+ | 1/8 |
The universal temperature controller KS 41-1 is intended for universal, precise, and cost-effective control tasks in all branches of industry. For this, the unit provides simple 2-point (on/off) control, continuous PID control, or 3-point stepping control. The process value signal is connected via a universal input. A supplementary analog input can be used for heating current measurement or as an external setpoint input.
The KS 41-1 has three process outputs that can be 3 relays or 2 relays plus a universal output. This universal output can be used for operating a solid-state relay, a continuous current/voltage output or to energize a two-wire transmitter.
This controller is particularly well suited to the following industry applications:
Furnaces and ovens
Burners and boilers
Plastics processing
Driers
| Manufacturer | Series | Din Size |
|---|---|---|
| West Control Solutions | KS 41-1 | 1/8 |
The universal temperature controller KS 40-1 is intended for universal, precise, and cost-effective control tasks in all branches of industry. For this, the unit provides simple 2-point (on/off) control, continuous PID control, or 3-point stepping control. The process value signal is connected via a universal input. A supplementary analog input can be used for heating current measurement or as an external setpoint input.
The KS 40-1 has three process outputs that can be 3 relays or 2 relays plus a universal output. This universal output can be used for operating a solid-state relay, a continuous current/voltage output or to energize a two-wire transmitter.
This controller is particularly well suited to the following industry applications:
Furnaces and ovens
Burners and boilers
Plastics processing
Driers
| Manufacturer | Series | Din Size |
|---|---|---|
| West Control Solutions | KS 40-1 | 1/8 |
The universal temperature controller KS 42-1 is intended for universal, precise, and cost-effective control tasks in all branches of industry. For this, the unit provides simple 2-point (on/off) control, continuous PID control, or 3-point stepping control. The process value signal is connected via a universal input. A supplementary analog input can be used for heating current measurement or as an external setpoint input.
The KS 42-1 has three process outputs that can be 3 relays or 2 relays plus a universal output. This universal output can be used for operating a solid-state relay, a continuous current/voltage output or to energize a two-wire transmitter.
This controller is particularly well suited to the following industry applications:
Furnaces and ovens
Burners and boilers
Plastics processing
Driers
| Manufacturer | Series | Din Size |
|---|---|---|
| West Control Solutions | KS42-1 | 1/4 |
Reviews
There are no reviews yet.